“All our accumulators are dispatched without pre-charge. A pre-charge incurs additional cost. For more information contact us on email@example.com or call us on 03 9272 8900.”
HYDAC piston accumulators are hydropneumatic accumulators. Indeed, its floating piston serves as a separation element between a compressible gas cushion and the operating fluid.
First of all, their components are:
- A cylindrical jacket with a finely processed interior, a screwed-in cover on the gas and fluid side as a rule
- And a piston with special sealing systems
Therefore, the adjustment of the piston accumulators can be very flexible according to customer requirements.
What's more, selection of the volume is practically stepless. Also, the piston position can be visible and be serving for switching functions in the hydraulic system.
- Nominal volume: up to 3,300 l
- Permitted operating pressure: up to 1,000 bar
- Piston velocity: dependent on sealing system, usually up to 5 m/s; higher velocities possible
- Accumulator shell materials: carbon steel, stainless steel, aluminum
- The minimal pressure differential between the fluid side and gas side
- Large usable volumes
- A variable installation position
- Monitoring of the piston position possible using various systems
- Particularly suitable for backup configurations
- Also, an extreme flow rates
- And no sudden discharge of gas when seals are worn
- What is a hydraulic accumulator?
Hydraulic accumulators are closed pressure vessels designed to store then discharge pressurised fluids.
A hydraulic accumulator consists of a fluid section and a gas section with a gas-proof separation element between them.
The fluid section of the accumulator is connected to the hydraulic circuit so that as the hydraulic system pressure increases the gas is compressed. When the pressure drops, the compressed gas expands and forces the stored fluid into the circuit.What are some of the reasons to use an accumulator in a hydraulic circuit?
Some of the most common applications for hydraulic accumulators are:
- energy storage,
- emergency and safety functions
- damping of vibrations, fluctuations, pulsations (pulsation damper), shocks (shock absorber) and noise (silencer)
- volume and leakage oil adjustment, and
- energy recovery
Each of these varied applications may require specialist knowledge in order to select and configure the correct accumulator.What are the most common types of accumulators?
Hydraulic accumulator types are defined by the gas-proof separation element.
The most common hydraulic accumulators are diaphragm, bladder and piston. Metal bellows accumulators are available but are less common in the Australian market.
Each hydraulic accumulator type is available in different sizes and can be selected for specific applications.What gas should I use to pre-charge an accumulator and what should my pre-charge pressure be?
Hydraulic accumulators must be pre-charged with an inert gas, typically nitrogen (Class 4.0, filtration < 3μm). Compressed air or oxygen should never be used due to risk of explosion.
For energy storage applications, the pre-charge pressure must be less than or equal to 90 per cent of the minimum operating pressure of the hydraulic system.
Contact HYDAC if gases other than nitrogen are used or for information regarding pre-charge pressure for different applications.What are some of the safety considerations for accumulators?
Hydraulic accumulators are subject to high pressures; therefore no welding, soldering or mechanical work can be carried out on them.
HYDAC recommends that all hydraulic accumulators have a dedicated relief valve and a method of isolating and bleeding the accumulator as this will ensure the correct and safe application.What are the main differences between a diaphragm and bladder-type accumulator?
Hydraulic accumulator types are defined by their gas-proof separation element. The most common hydraulic accumulators are diaphragm and bladder in the Australian market. Each hydraulic accumulator type is available in different sizes and can be selected for specific applications.
Diaphragm accumulators are usually not repairable and typically small in size, ranging from 0.075L to 4L.
Bladder accumulators are the most common accumulator type and typically range between 0.5L to 200L.Are diaphragm or bladder accumulators repairable?
Due to the nature of diaphragm accumulators typically being a weld-type design, they are not repairable.
However the bladder accumulators are serviceable and repairable and spare components such as bladders, poppet valves and anti-extrusion rings etc. are readily available.Do hydraulic accumulators need to meet any certifications, approvals or regulations?
Hydraulic accumulators in Australia are designed and constructed in accordance with AS1210 and are subject to AS/NZS 3788 when in service.
For more information, click here to watch HYDAC’s webinar.